Turnkey Production Services That Eliminate Risk and Protect Uptime

Whether you're facing capacity constraints, demanding surface specs, or compliance pressures, SurfacePrep delivers outsourced production support that works like an extension of your line. A fast, traceable, and performance-proven system you can rely on.

What We Deliver

Certified to Perform & Audited to Deliver

• ISO and AS-certified processing at multiple regional locations
• Full process traceability and documentation

Emergency* Capacity Relief

• Projects can be assimilated in 24-72 hrs
• Flexible scheduling, same-day logistics support
• No long-term commitment required

High-Precision, High-Volume

• Consistent finish across volumes of parts
• Precision process controls
• Repeatable, documented process flows

Surface Preparation Services Provided

SurfacePrep is proud to offer a wide variety of surface preparation services.
These services include but are not limited to:

• Abrasive Blasting
• Shot Blasting
• Powder Coating
• Fabrication – Short Run & Specialty
• Precision Hand Finishing
• Robotic Finishing
• Electropolish – Dry & Suspension
• Laser Marking/Engraving

• Mass Finishing
  • Deburring
  • Precision Surface Finishing
  • Mirror & Ultrapolishing
  • Accelerated Isotropic Finishing
  • Drag Finishing

• Cleaning
  • Spray
  • Immersion
  • Ultrasonic Vacuum U/S
  • Passivation

Certifications That De-Risk Your Decision

Certified to Perform & Audited to Deliver

When reliability is non-negotiable, our certifications speak volumes. SurfacePrep is fully equipped to meet the compliance standards that govern aerospace, medical, defense, and high-spec manufacturing environments.
Terms & Conditions »
Service details »

Our Certifications Include:

• ISO 9001:2015 – Proven quality management across all operations
• AS9100D (Aerospace) – Flight-critical process control, traceability, and documentation
• ISO 13485:2016 (Medical Devices) – Process isolation, risk mitigation, and regulatory readiness

What this means for you:

• Seamless supplier qualification
• Audit-ready documentation on every batch
• Trusted by OEMs and Tier 1s across North America

We pass your audits, so you can pass theirs.

Did You Know?

We perform flow path surface finishing of flight critical titanium castings.
Surface finishing of cast titanium flow path channels is key to drag reduction and engine performance. At SurfacePrep Production Services division, we have mechanical finishing processes and systems dedicated to this task. In the event mechanical flow path finishing processes are not approved for a particular part number, we offer approved precision hand finish processing of these same features. AS9100D certified, our production facilities cater to stringent aerospace structural and rotating component requirements.

We perform medical implant finishing, cleaning and passivation services.
Orthopedic implants can have a wide range of surface finish requirements. Polished articulating surfaces are typical. Bone growth areas are often prepared via air blast with large grit aluminum oxides. Satin finished bone plates and other trauma components are often prepared with glass bead abrasives. Regardless of the surface finish requirement, via precision hand finishing, drag or other mass finishing methods, robotic belting or dry electropolish (DLyte), SurfacePrep's ISO 13485:2016 certified production services are available to be your finishing department.

We offer production ultrasonic cleaning, passivation and laser marking process capabilities.
After surface finishing, ultrasonic or immersion cleaning and passivation typically follow. Ultrasonic or immersion cleaning remove soils and particulate from the parts. Where some manufacturers do not allow use of ultrasonics on their parts, we also provide cleaning under vacuum which can intensify the cleaning process and drive access to tapped, blind holes or porous surfaces. Passivation, whether citric or nitric based (see ASTM A967) works to remove free-iron that may have attached or imbedded in the finished surface. At SurfacePrep, we offer production cleaning (ultrasonic, immersion, vacuum) and laser marking services focused on the medical device and aerospace component industries. We are AS9100D, ISO13485:2016 Certified.

We possess in-house automated robotic finishing capabilities.
Production surface finishing via manual hand finishing techniques are often the most flexible methods. However, some components lend themselves to the opportunity for robotic automation. In these cases, SurfacePrep blends our manual process experience with our mechanical finishing expertise to create robust and repeatable automated finishing processes. Aerospace components and medical devices alike can benefit from this approach. Expert preparation, masking and post process cleaning are offered to complete the requirements. AS9100D, ISO13485:2016.

Why SurfacePrep?

Ready to Offload Work or Add Resilience?
Reach out below or call us at (888) 873-1066 to speak to a finishing engineer.

1. Request a Capacity Review
   We'll assess your part specs, volumes, and turnaround needs.
2. Receive Your Quote & Process Plan
   Our engineers build a custom finishing workflow: abrasives, chemistry, equipment and method.
3. Start Processing
   You get full transparency, traceable results, and a single point of contact.

Production Services Locations